BOHNING NOCK UNI SUPER BUSHING BK
Pack of 100 pieces
BOHNING NOCK UNI SUPER BUSHING AP
Pack of 100 pieces
BOHNING NOCK UNI SUPER BUSHING LM
Pack of 100 pieces
BOHNING NOCK UNI SUPER BUSHING RS
Pack of 100 pieces
BOHNING NOCK UNI SUPER BUSHING NO
Pack of 100 pieces
Bohning’s Blazer® Nock fits standard carbon shafts with an ID of .246″ (6.25mm, but commonly known as 6.5mm) and Super UNI Bushing systems. The Blazer® Nock features a double-lock throat and a raised index. Its throat size is .120″ (3.05mm) and each Blazer® Nock weighs an average of 9.0 grains (583.2 mg). Tech tip: for easier insertion and indexing, apply a small amount of Bohning’s Tex-Tite or Seal-Tite Wax to the nock shank.
NOT ALL BRANDS OF NOCKS ARE CREATED EQUAL At Bohning, every nock style must pass the following steps before introduction to the market:
1. Computer simulations identify potential weak points.
2. Destructive testing methods expose possible design flaws or material defects.
3. Accelerated life cycle testing using a custom-built bow is performed at kinetic energy levels exceeding 110 ft-lbs (nearly twice that of most hunting bows). A single nock must withstand over 1000 shots or it goes back to step 1.
Proudly manufactured at the Bohning Factory in Lake City, Michigan, United States.
Pack of 100 pieces
Insert nocks for shafts with 6.2mm inside diameter. Known also as -60 or Super UNI.
Available in the following colors: fluo yellow, fluo red, fluo...
16 other products in the same category:
Finally a new system for the positioning of the arrow on the bow. The new ThunderBall system is mounted within a few minutes and eliminates any...
Features:
Precise contact points for controlled arrow release.
Concentric design to center the nock in the arrow shaft for more consistent...
Insert nocks for shafts with 6.2mm inside diameter. Known also as -60 or Super UNI.
Available in the following colors: fluo yellow, fluo red, fluo...
Features:
Precise contact points for controlled arrow release.
Concentric design to center the nock in the arrow shaft for more consistent...
The Beiter Plug-in Nocks were originally developed for use as Nocks that are plugged directly into the aluminium shafts (instead of on the cone or...
In-Out nocks are designed to enter inside A.C.E. or X10 shafts. At the same time they cover the external side of the shaft itself in order to...
Available in the following colours:
BK: Black
FG: Green
OR: Orange
WH: White
YL: Yellow
The Beiter Insert-Nock .166" has been designed to be inserted directly into Aluminum Shafts (instead of the cone or a Bushing!), but became very...
Insert nocks for shafts with 6.2mm inside diameter. Known also as -60 or Super UNI.
Profile particularly appreciated by 3D shooters.
Available in...
Nock suitable for Cross-X Fulmen shafts and all shafts with an internal diameter of .244.
Symmetric nocks, which can be used on every Easton and Beman shaft equipped with this system. They are ideal if you use a loop on the string....
The 4mm G Nock is the heaviest 4mm Nock weighing in at 7 grains. The 4mm G Nock is compatible with the Inspire carbon arrow as with the Super...
Nock 3-18/2,
Colour: Green
Kategorie: In-Nocken #2
The Beiter Plug-in Nocks were originally developed for use as Nocks that are plugged directly into the aluminium shafts (instead of on the cone or...
